Whole house rewire in San Diego, without gutting the house.
Old wiring is a real fire risk and an insurance problem. The pros we send rewire homes in phases, circuit by circuit, room by room, using fish tape, attic and crawlspace runs, and minimal-cut wall openings to keep the drywall repairs small. Permit pulled, every circuit AFCI-protected, every install inspected.
Rewiring included
- Knob-and-tube rewire with insurance documentation
- Aluminum wire remediation: full replacement or COPALUM crimp connections
- Failing copper rewires (cracked insulation, open splices, scorched conductors)
- Phased rewires done one circuit or one room at a time with no full-house power loss
- New AFCI/GFCI breakers per current NEC
- Add new circuits for kitchen, laundry, garage, EV charger, HVAC equipment
- Smoke and CO detector hardwire updates
- Drywall opening minimization with attic + crawlspace pulls when possible
When this is the right call
- Home was built before 1960 and still has original wiring
- Insurance company flagged knob-and-tube or aluminum wiring
- Two-prong outlets throughout the house (no equipment grounding)
- Frequent breaker trips, flickering lights, or warm switches
- Burning smell or scorch marks at outlets, switches, or fixtures
- Major remodel or addition that exceeds existing panel/circuit capacity
- Pre-purchase inspection identified wiring problems
Rewire, partial repair, or something smaller
The insurer flagged knob-and-tube or aluminum branch wiring
Treat that as a rewire conversation, not a one-outlet repair. Carriers in California often refuse to renew on active knob-and-tube or unremediated aluminum. A licensed C-10 can document a partial or staged rewire so the policy can be renewed without opening every wall on day one.
The house still has two-prong outlets in most rooms
That usually means there is no equipment ground on those circuits. Swapping to a three-prong device without a real ground or a labeled GFCI is not a fix. The electrician traces whether a ground can be pulled, a GFCI can be labeled, or the branch has to be recabled.
One room has failing outlets or cloth-covered wire, the rest of the house is fine
A partial rewire of that area is often the right first job. Whole-house work is for original wiring throughout, an insurance demand, or a remodel that already has the walls open.
You want an EV charger or a heat pump on original 1960s wiring
New loads belong on new circuits from a panel that can take them. The electrician runs a load calc first. A charger does not require a full rewire by itself, but original ungrounded or aluminum circuits serving that garage often have to be replaced as part of the same visit.
Rewiring the network covers
These calls come in under a lot of different names, and the electricians we connect you with handle all of them across San Diego County: house rewiring, whole home rewiring, electrical rewiring, knob and tube wiring replacement, and aluminum wiring replacement. Describe the job in whatever words make sense to you when you call, and the operator sorts out the actual scope before anyone is dispatched.
Common Whole House Rewire questions
How much does it cost to rewire a house in San Diego?
Whole-home rewires for a typical 1,500–2,500 sq ft single-family home run $12,000 to $28,000, depending on access (slab vs. crawlspace), wall finish (lath-and-plaster is harder), and how much drywall patching is in scope. Partial rewires start around $3,500 for a single problem area. Ask for a written quote before work starts.
Do I have to move out during a rewire?
Almost never. The electricians we connect you with work in phases, one circuit or one room at a time, so the rest of the house stays powered. Most clients stay in the home through the entire project. They'll let you know in advance which rooms will be without power, and for how long.
How much drywall damage should I expect?
Less than you think. The pros we send pull through attic, crawlspace, and existing chases wherever possible, and use fish tape through walls when not. Most rewires need 4–8 small drywall openings per room. We don't do drywall repair ourselves; we'll refer a finisher or coordinate with yours.
Will my insurance company approve the rewire?
Yes, and they often require it. The electricians we connect you with provide a written scope, permit copy, and inspection sign-off your insurance agent can submit. Knob-and-tube and aluminum wire homes are difficult or impossible to insure; once rewired, your premium drops and your renewal goes through.
Can I do a partial rewire instead?
Yes. A partial is the right answer when only one circuit or one area has problems. The pros we connect you with handle kitchen-only rewires, laundry/garage circuit additions, knob-and-tube in just the original part of the house. They won't push you to do more than the home actually needs.
Can you repair aluminum wiring without a full rewire?
Often, yes. The recognized remediation for older aluminum branch wiring is a copper pigtail at every device and junction using AlumiConn or COPALUM connectors, which addresses the actual failure point, the connections, without opening every wall. A full copper rewire is the permanent fix and the right call when walls are already open or the wiring has other problems. The pro lays out both scopes after an inspection.
Whole House Rewire across San Diego County
The electricians in our network cover whole house rewire in every city and community in San Diego County. Pick your city for local climate notes and service specifics.
See whole house rewire in all 67 cities
Need whole house rewire in San Diego County?
Call and we'll match you with a licensed C-10 electrician for the job.